#Automotive meter es 585 owners manual install
#Automotive meter es 585 owners manual professional

DO NOT LEAVE DEAD BATTERIES INSIDE THE CONTROL BOX. IMPORTANT: TO PREVENT DAMAGE TO THE REF-METER-OCTA, CAREFULLY OBSERVE BATTERY POLARITY AS MARKED INSIDE THE BATTERY COMPARTMENT. Replace battery cover by aligning tabs and snapping back into place. If necessary, remove old set of batteries.ДЈ. Remove the battery cover from the rear of the control box by compressing tab at the base of the battery cover.Дў. Replace the REF-METER-OCTA into the carry bag.ДЎ. Push the control box firmly into the storage dock of the weighing platform until it snaps in place.Д¤. Hold the control box and press the yellow auto reel button on the side of the platform.ДЈ. If extended, restore the easel of the control box to the retracted position.Дў. When using the REF-METER-OCTA, ensure the cable does not touch the top of the weighing platform to avoid inaccuracies.ДЎ. Pull out the control box from the storage dock. The storage dock is placed on the low side of the weighing platform.ДЈ. Push the signed part of the control box to remove it from the storage dock. Remove the REF-METER-OCTA from the carry bag.Дў. The last state of the REF-METER-OCTA will be restored upon power-up.ДЎ. To conserve battery life, the REF-METER-OCTA will turn itself off after 30 minutes of inactivity, unless it is currently running a program (see Programming section). Turn the REF-METER-OCTA off by pressing down.Д§. A negative number indicates the applied weight is less than the zero value.Д¦. A positive number indicates the applied weight is greater than the zero value. Place the material to measure in the container or on the center of the platform.ДҐ. If using a container to hold the objects being measured, place it empty on the center of the platform.Дў. Select the desired display resolution by repeatedly pressing as described in the RESOLUTION section.ДЎ. Kilograms Г– pounds Г– pounds and ounces Г– ouncesД¦. Select the proper measurement units by repeated pressing. Place the Weighing Platform on a firm, level surface.Д¤.

#Automotive meter es 585 owners manual install

Install the batteries into the control box as described in the вЂњBattery InstallationвЂќ section below.ДЈ. Unpack the scale as described in the вЂњUnpacking the REF-METER-OCTAвЂќ section below.Дў. To operate the REF-METER-OCTA as a basic weigh scale, perform the following steps:ДЎ. NOTE: To prevent damage, never exceed the rated capacity of the REF-METER-OCTA. Thread for mounting 10612-REF for liquid filling and charging of refrigerants cansД .5% of Reading +/- 1 Least Significant DigitДЈ0.5 cm x 30.5 cm x 4.5 cm (12.0вЂќ x 12.0вЂќ x 1.8вЂќ).Can be calibrated in the field with inexpensive reference weights.Built-in memory remembers all previous settings.Attaching the REF-METER-OCTA to the REF-METER- OCTA-PLUS allows automatic refrigerant charging for A/C systems. The REF- METER-OCTA is programmable, and has a built in alarm to indicate a programmed threshold has been exceeded. With the REF-METER-OCTA, you can measure weight in both kgs and lbs units. It is ideal for HVAC and Refrigeration service, including Critical Charging of small refrigeration systems. The REF- METER-OCTA is the most accurate and precise refrigerant meter available today with features that cannot be found anywhere else. Diode Test Test current 0.6 mA, Open circuit voltage 3.0V.Thank you for your purchase of the REF-METER-OCTA Digital Charging Scale.

Dwell Angle 3 cyl, 4 cyl, 5 cyl, 6 cyl, 8 cyl.

Fuse protected, safety leads and jacks.

Measures Volts, Ohms, Amps, RPM, Frequency, Temp., Duty Cycle, Dwell, Continuity & more!.

Analog Bargraph Display and Large Digits.

The #585 includes two sets of test leads, RPM inductive pick-up, temperature probe, soft zippered case and instruction manual. Among its testing capabilities are: AC/DC Volts, AC/DC Amps, Ohms, RPM, Dwell, Frequency, Duty Cycle, Temperature, Continuity and more.

#Automotive meter es 585 owners manual professional

The 585 is an automotive meter that does it all! This is a professional grade tool used for diagnosing electrical, computer and engine problems on any vehicle.